wear tester

The Repair of Tear and Wear Tester and Its Research and Development of Test

摩擦磨损试验机的修复及其试验的研究开发

Design and application of data processing system for friction and wear tester in LabVIEW environment have been presented.

为加速判断扶正器性能优劣，指导生产，研制与之相应的摩擦磨损试验台就变得非常有意义。

Abrasion wear test of Fe-20% Cr ahoy with carbon content ranging from 0.82% to 2.94% was conducted at 800 ℃ in a self-made high temperature wear tester. The worn surfaces and subsurfaces were observed by SEM.

本文用自制的高温磨损试验机对碳含量0.82～2.94%的Fe-20%Cr合金进行了800℃下的高温磨损试验，并用扫描电镜观察了磨损面和磨损面亚表面的情况。

The results of the wear tests performed in the TNO tester and the bearing tester also indicate this application.

在TNO试验机和轴承试验机上进行的磨损试验也说明了这种应用。

Fretting wear behavior of CuS nanoparticles in urea grease was studied in fretting wear tester.

在微动磨损试验机上考察了含有硫化铜纳米粒子脲基脂的微动磨损性能.

Based on virtual technology, a new friction and wear tester used for the testing of the water-lubricated bearing was put forward.

介绍了所设计的基于虚拟仪器技术的水润滑轴承摩擦磨损实验机。

The wear resistance are measured through M-200 wear tester and ML-100 abrasive wear tester at room temperature.

在室温条件下，在M-200型磨损试验机、ML-100型磨料磨损试验机上进行渗硼层的磨损试验。

Wear resistance of the coatings was tested on abrasion tester and the wear appearance of the coatings was investigated by SEM.

在磨损试验机上对其耐磨性进行测试，同时利用扫描电镜对试样的磨损形貌进行观察分析。

A Controlled Atmosphere High Temperature Oxidation Wear Tester

可控气氛高温氧化磨损试验机的研制

The coefficient of friction and hard-wearing of nano cemented carbide are studied by ball-on-disk friction and wear tester, the worn surface is observed by SEM, and the wear mechanism is studied.

首先利用球盘式摩擦磨损试验机研究了纳米硬质合金的摩擦系数、耐磨损性，然后利用SEM观察了磨损表面，研究了磨损机理。

Impact wear tests on tester MLD 10, single point impact test and ball on ball test have been carried out.

为此进行了MLD10的冲击磨损试验、单点冲击试验和落球试验。

Design and Analysis on the loading Mechanism of the KTL Wear-tester for Engine Cylinders

汽缸套模拟磨损试验机加载机构的力学研究

The tribological performance of five kinds of piston rings when lubricated with GF-3 fully-formulated engine oil was investigated on a SRV high temperature friction and wear tester.

利用SRV高温摩擦磨损试验机模拟发动机运行态条件，考察了五种活塞环在GF-3全配方发动机油润滑下的摩擦学性能。

The effect of varying mates on abrasive wear character of martensitic wear-resistant steel by MLD-10 type impact abrasion tester was investigated.

讨论了在动载三体磨粒磨损条件下，马氏体钢配副变化对磨粒磨损系统耐磨性的影响。